Dynalco SWTD-1000 Speed Switch/Transmitter Manual do Utilizador

3690 NW 53rd Street • Fort Lauderdale, FL 33309 • Ph 954-739-4300 • Fax 954-486-4968 • www.dynalco.com SWTD-1000 Speed Switch / T

Operating Instructions SWTD-1000 DYNALCO 8// 4.2 Machine Factor The machine factor establishes the relationship between sensor frequency (Hz) an

Operating Instructions SWTD-1000 DYNALCO 9// 5. Installation The SWTD-1000 may only be installed by trained and competent personnel. An undamag

Operating Instructions SWTD-1000 DYNALCO 10// 6.2 Terminals SWTD-1000 Sh 0VS Ana. +Vout Dig. +Bin +PO -PO NC NO Com +AO -AO Gnd +24V Sens

Operating Instructions SWTD-1000 DYNALCO 11// 7. Hardware Configuration 7.1 Analog Sensor Input (Sign) Jum

Operating Instructions SWTD-1000 DYNALCO 12// 8. Configuration with PC Software 8.1 Software Concept All settings are written via PC to the SWTD

Operating Instructions SWTD-1000 DYNALCO 13// 8.4 Parameter List and Ranges If you already have a configuration file you can open and view it

Operating Instructions SWTD-1000 DYNALCO 14// 8.5 Parameters Parameters are changed in the sub menus from the drop down menu “Configuration“. W

Operating Instructions SWTD-1000 DYNALCO 15// 8.5.3 Analog Output (Configuration Æ Analog Output) 21 20 12 4 0speed [RPM] 0...20mA mode 4...2

Operating Instructions SWTD-1000 DYNALCO 16// 8.5.5 Relay Parameter and Selection of Parameter Set (Configuration Æ Relay control) Parameter

Operating Instructions SWTD-1000 DYNALCO 17// 9. Operating Behavior 9.1 Power On 9.1.1 Analog Output Following power on the output assumes

TABLE OF CONTENTS 1. Safety Instructions 1 2. Product Features 1 3. Specifications 2 3.1 General 2 3.2 Inputs 3 3.2.1

Operating Instructions SWTD-1000 DYNALCO 18// 9.2.2 Signal Failure In the event of a sudden loss of a good signal no positive edge arrives to co

Operating Instructions SWTD-1000 DYNALCO 19// 9.3.5 Binary Input 2 functions are executable using the binary input: • Switching between parame

Operating Instructions SWTD-1000 DYNALCO 20// 10. Mechanical Construction / Housing Mounting Using DIN 43835 Form B clamps Terminals Detacha

Operating Instructions SWTD-1000 DYNALCO 1// 1. Safety Instructions SWTD-1000 may only be connected by trained & competent personnel. Be

Operating Instructions SWTD-1000 DYNALCO 2// 3. Specifications 3.1 General SWTD-1000 Lowest measuring range 0 . . . 1.000 Hz Highest measurin

Operating Instructions SWTD-1000 DYNALCO 3// Max. frequency against input voltage0.010.11101000.0010.010.1110100100010000100000Frequency [Hz]Inpu

Operating Instructions SWTD-1000 DYNALCO 4// 3.2.2 Digital Sensor Connection (IQ) Frequency range (-3dB) 0.01 Hz / 35 kHz Input impedance 46

Operating Instructions SWTD-1000 DYNALCO 5// 3.2.4 Binary Input Use For external selection of Parameter set A or B. • Logic 1 = Parameter s

Operating Instructions SWTD-1000 DYNALCO 6// 3.3.2 Relay Type Single Pole Double Throw Limit Hysteresis Programmable – 1 lower and 1 upper set

Operating Instructions SWTD-1000 DYNALCO 7// 4. Principle of Operation 4.1 General The SWTD-1000 is controlled by a microprocessor. It works acc